Book My Estimate

 

 

We've stumbled upon this article about Installing A Bathtub down the page on the net and felt it made sense to write about it with you in this article.

Installing a bath tub isn't specifically brain surgery, however it does need solid plumbing, woodworking, and also often, tiling abilities. Replacing an old bath tub with a brand-new one is likewise a moderately difficult project. If the old bathtub is easily easily accessible, the project can relocate immediately; if you have to open a wall surface to get rid of the old tub and place the brand-new tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub and embeded in the brand-new one. Ensure you have qualified on your own for the work as well as are comfortable attempting it. As opposed to working with a specialist to take over a halfway-completed project, it is much better to think about employing one prior to you start. Chances are you may require an expert plumber to make tube connections.
This short article will aid you set up a new bathtub in your washroom if you have currently gotten a new bathtub as well as don't require to change the setup of your previous supply of water pipelines.
Your tools and also material list need to make up the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Planning for the Setup

First of all, the sustaining framework provided with the bath must be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to see to it that if the tap features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its last placement.

 

 

Removing Old Touches

If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The procedure of removing the existing taps can be quite troublesome as a result of the limited access that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before moving on to fit the new faucets, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.

 

 

Mounting the Tub

Using both wood boards under its feet, place the bathtub in the called for placement. The wood boards are valuable in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 tiny points.
The next goal is to make certain that the tub is leveled all round. This can be accomplished by checking the level as well as changing the feet on the bathtub till the level reads level.
To mount taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the water supply and examine all joints and also brand-new pipework for leaks and tighten them if essential. Load the tub and additionally examine the overflow outlet and the regular outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the bathtub needs to wait up until the bath tub has been made use of a minimum of once as this will certainly settle it right into its final setting.

 

 

Fitting New Touches

If the tails of the new taps are plastic, after that you will require a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will call for lowering couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers remain in place between the faucet and also the sink. Secure the faucet in position with the producer given backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular tap adapters. The former kind should be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Bath tub

In the area where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to fracture a rigid seal, triggering the water to pass through the wall between the bathroom and the tiling, resulting in difficulties with wetness and feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes as well as cartridges, as well as can sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched paper or soft rope. Remember to always fill up the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in usage. The sealant can break relatively very early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also quickly offered on the marketplace. It is suggested to fit the floor tiles making use of water-resistant or waterproof adhesive and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you liked our section on A Step-by-Step Guide to Installing a Bathtub. Thanks a lot for spending some time to browse our short article. Enjoyed reading our posting? Please share it. Help others discover it. Thank you so much for your time spent reading it.

Book Now